Of course, you can always contact us with questions at: atlas ripe net or leave a more general comment below. The "Status" tab on your probe's information page will report information about suspected issues and give advice about how to fix them Please note that it takes up to four hours for probes to report an issue and for relevant information to appear on the Status page. When we have information about what might be wrong with your probe and detect a particular error, that information will appear under the "Status" tab on your probe's information page (you can see this by going to "My Atlas" and clicking on your probe's ID number). If neither of these has solved your problem, your probe will still be listed as "disconnected" or "abandoned". Hopefully that will solve the issue and you will see your probe listed as "connected" again within an hour of the stick re-initialising. Wait at least 30 minutes for the probe to initialise the drive and upgrade its firmware Plug in a new, brand-name USB stick that is at least 4GB in size (it does not need any preparation but its contents will be erased so make sure it does not store anything crucial)ĥ. Remove the current USB stick from the probeģ. If this is the case, please follow the instructions below (these are the same instructions you'll see on the "Status" page in both cases):Ģ. The error message will be about not detecting a flash drive or about having a read-only flash drive (see examples below). If your probe is still having issues with its USB stick, you should see a message under the "Status" tab on your probe's information page (you can see this by going to "My Atlas" and clicking on your probe's ID number). If the probe is still not connecting, advanced users may want to completely wipe the USB stick on another computer and try following these steps again. However, please note that we advise configuring your probe to use a static IP address only if you feel it is truly necessary to do so. When the probe is listed as "connected" again, it is safe to move the probe back to its original location. * If the probe was configured to use a static IP address, it will fetch it automatically. However, please note that this can take up to an hour to complete. Once the probe recognises that that the USB stick is present again, the process of downloading the fresh firmware will begin. (You can see SOS messages on your probe's detailed information page under the "Network" tab at the bottom of the page.)Īfter ten minutes, it is safe to re-insert the USB stick. Once the probe reboots, it will report the fact that it doesn't have a USB stick to the central RIPE Atlas system using a so-called "SOS" message. Please follow these simple steps (these are the same instructions you'll see on the "Status" page):ġ. If you have configured your probe to use a static IP address, the only thing you can do is move it to a network with working DHCP.* NOTE: This must be done on a network with working DHCP! It will NOT work if you have configured your probe to use a static IP address, because this mini-operating system does not have access to any statically configure IP addresses or DNS resolvers. If you've already tried this and you're still having issues, please In order to activate this last-resort option, the probe must be booted WITHOUT the USB stick. In turn, this causes the probe to remain "disconnected" from the RIPE Atlas back-end infrastructure.īelow we outline some steps to take to try to fix this issue, but it's important to note that the filesystem can always become corrupted again, so if you do run into problems with your probe disconnecting in the future, please repeat these steps.Īs a backup, if there is a problem with the USB stick, the probe hardware itself has a mini-operating system that enables it to download fresh firmware and save it on the USB stick once it is available again. In some cases, the filesystem on the probe can be corrupted, resulting in an unusable operating system. The USB stick on the version three (v3) probes is used to store both the operating system and the measurement data. RIPE Atlas users everywhere will thank you for getting your probe back online - and we will, too! (At the same time, we're also looking into a new hardware solution for the future.) If you've had trouble with your probe, please follow these simple steps. We're investigating what may be causing this issue and have a possible solution, outlined below. Some of the third version of RIPE Atlas probes have recently had an issue with their USB sticks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |